Roofing dumpster rental in Tempe
A low-wall 10-Yard Roll-Off Container drops in under two hours after the roofers clear out, then we haul it away.
Roofing Tear-off Dumpster Sizing by Squares
How big a roll-off do you actually need for a 25-square tear-off in Tempe? Most crews use a 20-yard container for asphalt shingles: one square requires two-thirds of a cubic yard. Our low-wall roll-off makes loading safer; the total tonnage remains the primary factor for disposal. You should calculate the weight carefully to avoid any unexpected extra fees.
15-Yard Roofing Dumpster
- Capacity: 15 cubic yards
- Fits: 15–20 squares of asphalt shingle
- Best for: Single-layer ranch and bungalow tear-offs
Our 10-yard can fits a tight driveway for small tear-offs, keeping shingle weight within tonnage for one single haul.
20-Yard Roofing Dumpster
- Capacity: 20 cubic yards
- Fits: 25–30 squares of asphalt shingle
- Best for: Most two-story residential tear-offs
The 20-Yard Container is a roofing workhorse because low side walls let crews ground-throw shingles without extra scaffolding.
30-Yard Roofing Dumpster
- Capacity: 30 cubic yards
- Fits: 35–45 squares of asphalt shingle
- Best for: Multi-layer tear-offs and small commercial roofs
For larger tear-offs with tight timelines, the 30-yard bin keeps crews moving without a second haul-out delay.
Asphalt Shingle Weight and Tonnage Planning
The three-tab shingle weighs about 250 pounds a square; architectural laminate runs closer to 400. A 25-square tear-off lands between three and five tons before underlayment, which is why the roofing dumpster routes lighter hooklift trucks with lower side walls to cap the weight limit on one trip. How does that translate to a 10-Yard?
When a project mixes shingle debris with framing or sheathing offcuts, we route that container as general C&D debris—the standard roofing rate no longer applies. We keep these material streams separate to ensure accurate processing at the facility.
Driveway Placement for Roofing Crew Workflow
Our crew in Tempe will angle the swing-door end of your roll-off toward the eave to maximize your workflow; we prioritize using driveway boards under every roller before the container touches the concrete. We maintain a six-foot tarp perimeter for a clean nail sweep after every job. You can review our roof tear-off container sizing or check the asphalt shingle disposal best practices guide to prepare your site. This ensures your driveway remains unscarred and efficient.
Drop angle
Rear door toward the roof line
Set the swing-door end facing the eave where the crew is working to keep walk-in loading and ground-throw paths aligned.
Surface protection
Wooden planks under every roller
Loaded shingle weight can gouge concrete; driveway boards stay under the rear rollers for the full rental window.
Sweep zone
Six-foot tarp perimeter
Stage magnetic sweepers on the tarp side so nail cleanup runs in parallel with loading your heavy materials.
Tile, Slate, and Metal Roof Tear-off Containers
Concrete tile, natural slate, and standing-seam metal punish a standard bin: they weigh two to four times what asphalt does. For these tear-offs, we route in a 30-yard container featuring reinforced sides and a heavier floor plate; we also cap the fill volume below the visual rim so the axle weight stays legal. We set these via lowboy for stability. For mixed loads, we also offer a general construction debris service to keep sites clear. Call (480) 646-3784.
Same-day Pickup for Fast Roof Project Turnover
Tear-off windows don’t wait; the roll-off has to move fast. Dispatch lines up same-day haul-out timed to the crew’s exit so the driveway clears for inspection, gutter reinstall, or the homeowner. We cover Maricopa with swap-outs to keep every job on schedule.